Видео

can yu changebtonthe old ones?

If my Ice Maker. Is at the bottom Does that mean that's where the reset button?

My ice falls from the bottom.

My ice Maker is at the bottom.

What are the sounds of bad spin bearings in a Whirlpool direct drive washer?

Your dryer motor video helped me out tremendously, thank you for your channel! Saved lots of money$ too.😉👍

Thank you very much. This was very helpful.

Great vid

Followed your steps and it went perfectly. Saved about $350 in parts markups and labor. Was $27.00 for controller on Amazon.

The room air passing through the evaporator isn't "chilled". The heat in the room air is absorbed by the evaporator.

First time in the fridge and it was easy! THANK YOU !!

Thanks !!

𝙊𝙠😊

My gasket doesn’t overlap like that the slots are much farther apart 5 - 6 inches maybe seems like a design flaw in my model

I have a stove similar the one in this video and it is the biggest burner that isn't working. It won't heat up. I replaced the switch and also replaced the burner and am still having the same problem. The burner won't heat up. Does anyone have any ideas on what the problem might be?

All of the tops you didn't orient the ball right. The top hooks set down in the ball

How did you remove the lower drawer on the oven I have that same stove, but can't get it out?

My brackets go from front to back and not from left to right. This makes it very difficult if not impossible to remove the bracket being that the screw that holds the bracket in place is at the rear. Does anyone have any ideas?

2:00 Problem here is, there are no wire harnesses to disconnect. The wires go straight to the burners. The brackets that hold the burners in place go from front to back just like in your video with the screw that holds the mounting bracket in place being at the back of the stove top. This makes it difficult if not impossible to remove the bracket. If the brackets went from left to right, this would make it much more user friendly. I am going to continue on and try to do this, but it would be nice to be able to remove the whole top like you do in the video.

I went on the Whirlpool website to purchase the large failed burner and found out all the burners are about $96.00 except for the one large burner that I need. That one, including taxes and shipping is $280.00!..... but still better than paying a repair person or buying a new stove.

I like the _soothing music_ in the background, it helps to destress me. I also like the clear closeups so I can see what you are doing.

Does the clutch stop agitating ?

Thanks dude

I gotta say this was a good video, BUT, I HATE HATE HATE the background music!! It was SO DISTRACTING! Who did you let ruin your great repair video with that stupid distracting "canned" bongo drum and geeeeetarrrrr music?! I had to keep stopping and rewatching several parts of it. Hate to say it but it ruined your video that has a lot of information and is difficult to follow anyway because of a LOT of info. Not even going to save it. Too painful. You should re-release the video with no background music.

This is a really pos dryer. So sorry I bought it.

Thank you so much, this was so helpful!

I'm so grateful for the detailed clear video ...my appreciation for you, boss 🌹

This is perfect. Just what I needed to feel like I could handle it.

Excellent video tutorial. I did a deeper dive replacing both valves and the drain pump and this video was really helpful! Thanks

It’s just like mine except for I don’t have the four screws holding the fan cover so I’m still searching for a video on how to do this. Very well done video just not mine.

I hate those new ones

Thank You! Man I LOVE RUclips!!!

Thank you sir

Were can I. Find it in vredenburg

What direction should this fan be spinning please, should it be blowing towards the coils or pulling air over the coils and blowing out the back?

Very helpful. Thank you

Lies. Its NOT this easy. The gasket will NOT just snap in all cute like they wanr you to believe.

gooooooood

thanks finally to the point

This video has the best repair music I’ve ever heard lol. Great video, perfectly explained, thank you!

Thanks!

I wish I had found this video before I threw my rack across the floor after dealing with the rack and rollers for hours. This should come in handy after I get the $9 part. Thank you.

Thank you Steve. So so very helpful. God bless amen

L90

Hi, Just wondering if you have a video to replace a GE 7.8 cu electric dryer w/steam Model # GTDS825EDMC? BUTTON WON'T COME BACK OUT. THANK YOU

If you take the top counterweight off first when preparing to remove the drum, it's much easier. The weight of the lower one keeps the top one's bolts easily accessible.

Thanks for this and all the videos 🤠

Thank you Steve ! You just save me 356$ 😂

Thank you sir.

This ice maker is a pain. Always stuck, hard to remove tray. Always melting. First few months it was fine. But of course it's a problem that the ice maker is stored in the fridge part and not with the freezer part.